12/19/2023 0 Comments Qbittorrent seeding meaning![]() ![]() I hope it this will help better understand what's all really about.Posts must be related to the discussion of digital torrents Ok I stop here because otherwise I'm going to write a tutorial. ![]() (I say potential because at a certain point of time you might only have a little part of the potentially interested peers able to connect you.) So absolute AND relative # have to be used to take a proper decision! Of course if the tracker(s) reports (with at best bt.scrape_stopped set on true which by the way is totally illogical to me because actually you want the scrape stop to be false but anyway.) 20 seeds it might not be necessary but also here it depends of the potential of real peers (leeches) too. Use this to get a good picture if and how much you should support the swarm again by seeding more. Here again the most important information is the overall availibility in the swarm AND the % completion for every connected peer (peers tab). In fact there is IMO an important information which is purely missing for good seeding in uT: You cannot (clearly) see what pieces you are uploading nor their single availibility within the swarm so you have to figure it out based on other information sources. Ĥ) Keep in mind that finally the only way to see if a swarm really needs you again as seeder, at a certain point of time you will have to shortly restart the torrent because only like this will you see if many peers need you and how much they really need you. I have never seen it well explained and clearly documented, only my experience and own "brainware" led me to this insight. I hope I could explain this point clearly enough. (Then follow how it may quickly go down again probably due the leeches who might disconnect soon to get some new bandwith for downloading (or seeding) other torrents.) If there would have been only 2 peers close to 100% in this example the avilibility # right from the point would be exactly the same but the increase after completion of the # left from the point would be only +2 max. Immediately you will see them disappear from your peers tab list and by this time the availibility # left from the point should increase by 5. So for instance if you see 5 peers out of 7 which have a completion level >98% and you are the only seeder than chances are high that in the following min there will be 5 seeds more. To be able to understand and see it you will have to check also the peers tab and pay attention to the % of completion for the connected peers. If the # left from the point is >2 >1 then there must be another seeder in addition to you seeding to the swarm But also here the very interesting (awesome) thing to note is that the # on the right will tell you much about the quality of the pieces available in the swarm however not about the quantity !! In other words there may be many potential seeders in the swarm but you cannot see it soley based on the availibility. Use this to see as a seeding client how many seeders are (potentially) in the swarm. Use observation and experience to get a better feeling.ģ) There is a very simple way which apparently too many people are not really aware of. Be aware that due to various technical limitations of the system (bittorrent implementing) the information shown in brackets can be totally false e.g. It can be very missleading so to get a better picture (but nevertheless it will never be accurate) always go to the trackers tab to have the overview and judge by yourself. Remember that this column shows only the connected peers with your client, nothing else.Ģ) The seed or peer # in brackets is simply tacken from tracker scrapes (http requests for status information) and uT has a strange kind of summing this information. Hence automatically your client will start to reject any other seeding peer which is the reason why you will always see 0 in the seed columns outside of the brackets. The same question for the seeds column, whilst you are below 100% you can see the number of seeds but when you hit 100% that number disappears, so how can you tell how many are still seeding with you?ġ) As soon as you have completed your download (without any partial file selection) you change your client status from peer (leech) to seed. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |